Page 13 - Highland Woodworking Tool Catalog

Table Saw Blades & Accessories
Dia. x Tooth Count Kerf * 1” bore
WOODWORKER II
General Purpose Table Saw
456005 12” x 40 * 1/8” $178.00 FORREST PREMIUM CARBIDE-TIPPED SAW BLADES
456001 10” x 40 1/8” $167.00 Of all the different makes of blades we’ve tried, none have cut as
456006 10” x 40 3/32” $167.00 well as a Forrest. Forrest guarantees their blades will completely
satisfy you, & our customers say it’s the absolute truth.
456003 9” x 40 1/8” $148.00
Woodworker II 40-tooth blades rip, crosscut & cut sheet
456004 8” x 40 3/32” $138.00 materials beautifully; we recommend 3/32” kerf for 1-1/2 hp &
WOODWORKER II 30-tooth smaller saws. Use the Woodworker II 30-tooth to rip thick stock.
456002 10” x 30 1/8” $148.00 WoodWorker II 48-tooth gives smooth cross-cuts. Woodworker II
WOODWORKER II 48-tooth Square Cut gives a dead flat bottom kerf for joinery cuts. For chop
192818 10” x 48 1/8” $172.00 & radial arm saws and crosscutting & joinery on the table saw, use
WOODWORKER II Square Cut Woodworker I crosscut blades. The Ply Veneer Worker has a steep
192819 10” x 40 1/8” $178.00 35° ATB design for veneered plywood & hardwood. Chopmaster
gives smooth cuts on miter saws. The Duraline High-A/T has a
WOODWORKER I Chop & Radial Arm very steep ATB design that slices veneered plywood, low pressure
456010 12” x 60 * 1/8” $188.00 laminates and solid wood
456011 10” x 60 3/32” $176.00 FORREST BLADE STIFFENERS with a nice, clean cut bot-
456012 9” x 60 3/32” $157.00 456023 456022 456021 tom surface.
4” $35.00 5” $37.00 6” $39.00
456013 8” x 60 3/32” $148.00
PLY VENEER WORKER FREUD SD208S 8” PRO DADO SET
Table & Radial Arm A high quality & economical dado set
192828 10” x 70 1/8” $185.00
for all 10” table saws, including SawStop!
CHOPMASTER BLADES Miter Saws 2 12-tooth negative-hook outside cutters & 3
456007 10” x 80 .105” $185.00 2-tooth chippers make clean flat bottom dados in
456008 12” x 80 * .115” $196.00 16ths from 1/4” to 7/8”. 5/8” bore. The TiCo Hi-Density carbide &
DURALINE HIGH-A/T BLADE silver I.C.E. coating reduces pitch build up & overheating. Due to a
Table Saws precise 8” dia. (not metric equivalent) & no anti-kickback teeth, it is
456027 10” x 80 1/8” $205.00 SawStop approved. SawStop dado cartridge is on page 15.
172042 Freud 8” Pro Dado Set (with steel shims & case) $109.99
INCRA 1000HD MITER GAUGE WITH FENCE
The top-of-the-line model of the Miter 1000 series.
The HD steel protractor plate with the AngleLOCK Indexing System
18” to 31” has 180 solid-lock stops in 1° increments. The GlideLOCK miter bar
TELESCOPING FENCE has 6 expansion disks to adjust both sides of the bar. The telescop-
ing IncraLOCK Cut-off Fence has a front T-slot to add a zero-clearance sub fence. With Incra’s patented
Flip Stop, & a steel vernier scale that reads to 1/10°,
this is the most solid & accurate miter gauge available. SET OF 6 MAGNETIC DADO SHIMS
107002 Magnetic Dado Shims $13.99
141023 1000HD Miter Gauge with Fence $219.99
(2 ea. .010”, .012” & .015”)
ZERO-CLEARANCE THROAT PLATES 168630 Delta (13-3/8” x 3-3/4”) $32.99
LENGTH ADJUSTMENT SIDE ADJUSTMENT SCREW (Left or Right Tilt Unisaw, Tilting Arbor & Contractors Saw)
SCREW REAR 168634 Delta 10” Direct Drive Saws $32.99
RETAINING
LEVELING PIN (12-1/2” x 3-3/4”)
SCREWS 168636 DeWalt 744 Saw (13-9/16” x 3-3/4”) $33.99
PRE-CUT 168640 Powermatic 66 (14-7/16” x 4”) $33.99
BLADE
POCKET 168637 General 350 (13-13/16” x 3-1/2”) $33.99
2-POINT SIDE BEARING LUGS UNDERNEATH 168638 Jet, Powermatic Artisan(12-1/2” x 3-1/2”) $33.99
One of the handiest accessories for your saw, (12-1/2” x 3-1/2”)
Leecraft custom throat plates provide solid stock 168639 Jet Xacta Left Tilt (13-5/16” x 3-11/16”) $33.99
support, prevent cut-off kickback & limit chip-out. 168631 Craftsman (14” x 3-3/4”x3/16”) $34.99
Our 1/2” thick melamine coated solid phenolic 168632 Older Craftsman (14-3/8” x 3-3/4”x 3/16”) $34.99
resin blanks are flatter, stiffer & slicker than any 168633 Sears-Pre 1960 (14-3/8” x 3-3/4” x 3/32”) $37.99
other throat plates you can buy. These plates 168024 RG-1 Rigid TXS3650 & TS3660 $34.99
cast iron top
feature lateral & end adjustment screws, 4 168023 JTSS Jet Supersaw JWS-10LFR $34.99
leveling screws (accessible from top), a steel 168027 Powermatic 72A (20-5/8” x 4”) $119.99
retaining pin to keep the blank’s rear from lifting 168624 CR4 Sears 21833 & Grizzly G0715P $38.99
(except on Jet & older Sears blanks), & a finger 168635 DeWalt 12” Miter Saws $17.99
hole. Grooves on the bottom house 10” saw (DW703, 704, 705, 705S,706, 713, 715, 716)
blades, so you can cut the blade opening without 168613 HT1 Hitachi & PC (15-1/8” x 3-3/4”) $34.99
needing a first cut with a smaller blade. Phenolic 168623 BH2 Bosch 4000/4100 w/o riving slot $34.99
blanks are big enough for 2 custom plates. 168628 1/2” x 11” x 15” Phenolic Blank $33.99
See our website for other models. 168629 1/4” x 11” x 15” Phenolic Blank $21.99
CARTER MAGFENCE II CARTER ACCURIGHT
Magnetic Bandsaw Fence BANDSAW TABLE INSERTS
A twist of 2 knobs engages 2-1/2” dia. nylon zero-clearance
powerful magnets that hold this throat plates virtually eliminate tear-out on the exit
15” x 3” high universal aluminum side of work. Saw a narrow kerf partway through
fence to your cast iron bandsaw table, avoiding te- the plate & drop it into the saw throat opening.
dious installation. T-slots accept attachments. 14” Bandsaw Table Inserts 3 pks $11.99 ea.
189262 MAGFENCE II Bandsaw Fence $139.99 189273 Jet 14” 189272 Delta & Steel City 14”
SEE OUR FULL LINE OF FORREST BLADES & DADOS ON OUR WEBSITE 13